Chest or Bust
Measure around the fullest part of the chest or bust, keeping the tape horizontal. This is a key measurement for work shirts, jackets, vests and coveralls.
BEETLE WORKWEAR / SIZING RESOURCES
Workwear Size Guide
Find the right starting point for sizing workwear, uniforms and protective apparel. Our workwear size guide explains how to measure employees, understand garment sizes and prepare accurate sizing information for business orders.
How to Measure
THE RIGHT FIT STARTS HERE
01
Measure the wearer
Record accurate body measurements.
02
Check the product chart
Compare measurements with the specific garment.
03
Confirm fit and movement
Consider daily tasks, layers and garment design.
BODY MEASUREMENT GUIDE
How to Measure for Workwear
Use a flexible measuring tape and measure over light clothing. Keep the tape level and comfortably close to the body without pulling it tight.
MEASUREMENT POINTS
01 — 04
Waist
Measure around the natural waist or the position specified by the garment chart. Trouser sizing may refer to a lower waist position.
Hips and Seat
Measure around the fullest part of the hips and seat. This helps assess the fit of work trousers, overalls and fitted uniform garments.
Inside Leg
Measure from the crotch to the required trouser hem position. An existing pair of correctly fitting trousers can also provide a useful inseam reference.
Before measuring:
Stand naturally, use a flexible tape, and
record the figures in inches or centimetres.
For jackets and coveralls, account for
the layers normally worn underneath.
MEASUREMENT REFERENCE
Workwear Sizing: Inches and Centimetres
This reference table converts body measurements between inches and centimetres. It is useful when comparing garment size charts that use different units.
Measurement Conversion Chart
1 inch = 2.54 centimetres
| Inches | Centimetres | Inches | Centimetres |
|---|---|---|---|
| 28" | 71.1 cm | 36" | 91.4 cm |
| 30" | 76.2 cm | 38" | 96.5 cm |
| 32" | 81.3 cm | 40" | 101.6 cm |
| 34" | 86.4 cm | 42" | 106.7 cm |
Important:
These numbers are exact unit conversions rounded to
one decimal place, not a garment size chart.
Sizes marked S, M, L, XL or with numerical codes
vary by manufacturer, style and fit.
Use the size chart attached to the individual product
to select the correct garment size.
SIZING BY GARMENT TYPE
Choose the Right Measurements for Each Garment
Different workwear products use different sizing measurements. Consider the garment's construction and working conditions before confirming employee sizes.
01
Work Shirts and Uniform Tops
Start with chest or bust measurements. Check the shoulder, sleeve and intended fit when selecting uniform shirts for employees.
Explore Uniform Work Shirts →
KEY MEASUREMENTS
Chest / Bust
Shoulder and sleeve fit
02
Work Trousers and Cargo Pants
Record waist and inside-leg measurements. Review seat room and knee positioning, especially for trousers with kneepad pockets or reinforced knee panels.
Explore Workwear Pants →
KEY MEASUREMENTS
Waist / Inseam
Seat and knee alignment
03
Coveralls and Overalls
Check chest, waist, height and inside leg against the product chart. Allow for the clothing normally worn underneath and confirm the fit when bending or reaching.
Explore Standard Coveralls →
KEY MEASUREMENTS
Chest / Waist
Height and inside leg
04
High-Visibility and Protective Workwear
Fit should allow normal movement without interfering with the garment's protective design. Check the manufacturer's sizing and the requirements of the workplace.
Explore High-Visibility Workwear →
KEY MEASUREMENTS
Product-specific
Fit and protective function
B2B WORKWEAR PLANNING
Preparing Sizes for a Team Order
For bulk workwear orders, collecting accurate employee measurements before placing an order helps purchasing teams organize sizes, quantities and future replacement requirements.
A workforce may require different garment fits, even when employees work in the same department. Record approved sizes against each specific product rather than assuming one size applies to every garment.
Get Business Sizing Support
TEAM SIZING CHECKLIST
✓
01
Identify garment styles and product references.
02
Collect employee measurements consistently.
03
Match measurements to each product's size chart.
04
Confirm sizes, quantities and fit requirements.
FREQUENTLY ASKED QUESTIONS
Workwear Sizing FAQs
Practical guidance for selecting garments and organizing business uniform orders.
Are workwear sizes the same as everyday clothing sizes?
Not always. Workwear sizing can differ by brand, fabric, fit and garment construction. Use body measurements and the specific product chart instead of relying only on a familiar clothing size.
Should employees order one size larger for coveralls?
Not automatically. Check the manufacturer's size chart and consider the layers worn underneath. The selected size should allow normal workplace movement.
Why is inside-leg measurement important?
Correct leg length helps prevent excess material at the hem and improves the positioning of knee features on certain work trousers.
How should businesses collect sizes for bulk orders?
Record measurements, chosen products and approved sizes separately for each employee. For large orders, a fit trial can help confirm garment selection before a full rollout.
WORKWEAR FOR BUSINESS TEAMS
Contact Beetle Workwear
Need Help Sizing Your Workforce?
Share your garment requirements, team size and available measurements to discuss workwear options for your business.